GMC  x   >   !Ford  x   >   International Trucks  x   >  

I have an old 1972 international scout II with a factory installed class II hitch. I have no wiring for a four pole electrical hook up. I did some searching on your website and saw that C58044 may be compatible with my Scout wiring. Is it? Do...

I have primus brake controler should I have 12 bolts from brake light switch or is it ground signal? | The brake light switch wire on the Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional # TK90160 should be positive....

What is the width of the frame bolt pattern? | The bolt holes on the Curt Trailer Hitch Receiver # C15302 sit across from each other 39" on center and are separated front to back by 7-1/2" on center. This is a custom fit for the following vehicles: 2008...

I have a 2009 international 4300 with air brakes .I want to pull my lowboy trailer that has vacum over hydraulic brakes . what do i need to do it THANKS | For your 2009 International 4300 with air brakes you will use the Hayes Air Actuated...

Best bolt on hitch plate for a 2001 international 4700 | The best option we have for your 2001 International 4700 is going to be a weld-on hitch plate. Unfortunately there are no bolt on options available for your truck. Make sure to use an...

I have a 2020 Dura star, there are two kits listed, what is meant by with on spot chainsinch and without on spot chains.? | OnSpot Chains are a special tire chain system for snowy weather (pictured below). Basically the sway bar is going to...

AIR TO ELECTRIC BRAKE CONTROL | We have the Hayes Air Actuated Trailer Brake Controller # HA100400C which is an air to electric brake controller like you need. This will connect to the air brakes of a trailer and allow you to operate electric...

What’s the inside dimension where the chassis would be? It looks like the 35 1/4 is outside to outside. | The inner bracket width of the Buyers Products Hitch Plate with 2" Receiver Tube - Ford # 3371809060A is 34-1/4" plus or minus 0.06" according...

I purchased the 3-in Reese super titan pintle mounting plate, and also purchased the Curt 30,000 lb pintle hook. When I tried to bolt the curt ain hook to the plate the bolts wont fit into the Reese super Titan pintle mounting plate. When...

We have an aftermarket bumper on our truck and Im trying to see if this hitch will work with it. What is the clearance from the top of the receiver tube to where it mounts on the frame? Also, what is the horizontal clearance of the mounting...

I have a 1999 International 3800 bus. I need a hitch for the rear of the bus. What would you recommend I use, is their a universal that would fit? | We do have some universal fit hitches that you'd be able to use on your 1999 International Trucks...

does this hitch come in a bolt on unit | The Super Titan 4000 Weld-On Trailer Hitch part # 38124 is a weld on application and does not come in a bolt on version. All of our heavy duty truck hitches are weld-on but the Buyers Products Class 4...

I’m considering purchasing the TSC to help reduce periodic sway with my 97 Airstream “Squarestream” fifth wheel. I’ve tried all I can do to eliminate periodic sway, including getting a much larger truck AND tweaking the hitch location along...

2005 International 8600 4x2 Day Cab Single Axle 10.8L I need a hitch to pull a car dolly behind it ASAP. PLEASE HELP | When it comes to installing a trailer hitch on your 2005 International 8600 4x2 Day Cab Single Axle I recommend The Curt Class...

will this hitch fit my 1995 International 4700 series truck | The Super Titan 4000 Weld-On Trailer Hitch part # 38124 will fit your 1995 International 4700 Series truck if the frame is approximately 34-1/4" to 34-3/4" which is the standard width...

Have a 2016 International 4300 with air brakes. I need to install a 7-pin trailer plug but the truck does not have any of the wiring to accommodate a trailer plug. What wiring harnesses, fuses, or relays do I need to make this work? I also...

Hi, I am looking to install a gooseneck trailer hitch on a 1996 International 8100 tractor. The inside dimensions between the frame rails is approximately 33 1/2. What are the dimensions for the BWGNRK1111 and will it fit without to many...

Hello, I have a rear engine 2001 International schoolbus . I want a bolt on tow package to tow my car. Please recommend a product Pics attached. Thank you! | When it comes to installing a tow hitch on your 2001 International school bus the only...

What hitches do you have for a 2000 international 4900 truck. Class 4 or class 5 | There are a few options for your 2000 International 4900 Truck, but there is not a custom fit receiver available. The Super Titan 4000 Weld-On Trailer Hitch...

I plan to tow a Big Tex 25 ft gooseneck trailer four brakes with a 2007 International 4400 SBA truck tractor with air brakes. What is the recommended controller and wiring kit. Does the controller wire into the switched side of the brake light...

I also tow small trailers, as well as a 12,400lb camper. Should I get a time delay controller? | In regards to choosing an electric trailer brake controller, you have proportional and time-delayed options. The best option would be a proportional...

What type on landing gear will you recommend for a 2004 International 4300 24ft 26,000GVW? I want to install one that way the truck is not shaking when forklifts go in and out. | The best option we will have is the Bulldog Square Jack - Drop...

Hello, will this receiver work with the factory step bumper on my 1977 Scout?? thank you, | Yes, the Curt Hitch part # 13580 that you referenced is a confirmed fit for your 1977 International Trucks Scout II that has a factory step bumper. Bumper...

I have a 2000 international 4900 tractor trailer I’m going to install a pintle hook to carry up to 50,000 pounds. What is the weight rating on this item? | While the Buyers Products Fabricators Hitch Plate # 3371809027A does not carry a weight...